subcooling n.1.低溫冷卻，局部冷卻。2.欠火候，加熱不足。
n. 1.低溫冷卻，局部冷卻。 2.欠火候，加熱不足。 “degree of subcooling“ 中文翻譯： 過冷度“heat of subcooling“ 中文翻譯： 再冷卻熱“subcooling austenite“ 中文翻譯： 過冷奧氏體“subcooling boiling“ 中文翻譯： 欠熱沸騰,過冷沸騰“subcooling condensate“ 中文翻譯： 過冷凝液“subcooling condenser“ 中文翻譯： 低溫冷凝器; 低溫冷卻器“subcooling margin“ 中文翻譯： 過冷裕度“subcooling conde er“ 中文翻譯： 低溫冷卻器“subcooling refrigerating effect“ 中文翻譯： 過冷卻產冷量, 再冷卻制冷能力“subcooler“ 中文翻譯： 低溫冷卻器; 過冷器；過冷裝置; 過冷卻器; 過泠卻器; 局部冷卻器; 再冷卻器“subcooled water“ 中文翻譯： 過冷水“subcooled temperature of open valve“ 中文翻譯： 開閥過冷度“subcooled temperature of open ale“ 中文翻譯： 開閥過冷度“subcooled temperature of close valve“ 中文翻譯： 關閥過冷度
subcostal |
|
Through the experiment , the following results were given out , whether the system was rolling or not , there were always density oscillation gradients when the two - phase flow instabilities occurred , and the stability of the system was always strengthened with the increasing of the inlet mass flow or the increasing of the inlet subcooling of the test tube 實驗結果表明，無論是搖擺還是不搖擺，系統發生的不穩定類型中都有密度波型脈動成分，系統的穩定性總是隨流量的增加而增強，隨入口過冷度的增加而增強。 |
|
According to rigorous procedures , an experimental study was carried out to investigate the effects of jet exit velocity , flow direction , fluid subcooling and nozzle diameter on hysteresis of boiling heat transfer with impinging circular submerged jets of highly - wetting liquids 摘要系統地研究了液體在圓形斷面噴嘴浸沒射流作用下沸騰熱滯后與射流沖擊速度大小、液體流動方向、液體過冷度和噴嘴直徑等因素的影響。 |
|
The experimental results showed that incipient boiling point decreased with increasing fluid subcooling and was independent of other factors , and that temperature overshoot enhanced with decreasing jet velocity and fluid subcooling 結果表明：沸騰起始過熱度隨液體過冷度增加而減小，與其他因素無關，而溫度過頭值則隨射流速度和液體過冷度減小而增加。 |
|
Based on the refrigerant state , divides a heat exchanger into three zones with zoned lump method , i . e . superheat , two - phase and subcooling zones , works out the temperature difference and heat transfer coefficients of the three zones 采用分區參數法將換熱器按制冷劑狀態分為過熱、兩相、過冷三區，分別計算了各區的換熱溫差、傳熱系數等。 |
|
The absence of both high and low side service valves precluded measurement of superheat and subcooling correctly 在上面和下面都應該安裝檢修閥,以便溫度過高和過低時能夠準確的測量 |