x
uploads/grid.jpg

grid n.1.格子,格柵。2.(蓄電池的)鉛板。3.【無線電】...

grid bias

There are many “ laws “ that govern the grids 有許多管理支配網格的“法則”存在。

A widget can span several cells in the grid 窗口小部件可以跨網格中的幾個單元。

You are not too disheartened by third on the grid 排在第三起步你并不是很沮喪?

This is where grid technology proves itself 這就是網格技術體現自己價值的地方。

Copy the information in the grid to the clipboard 將網格中的信息復制到剪貼板。

An additional factor which plays apart in estimation of the values at the grid nodes is weighting to be placed on the different data values located by the nearest neighbor search . 在估計網絡結點值時,部分起用以另一個因素及對最鄰近點搜尋中找出的不同數據值所給的權。

This alloy is a bit tricky as it sometimes may harden in the first twenty four hours after casting, becoming almost brittle, and produce cracks in the grid frames, etc . 這種合金制造有些棘手,因為有時鑄造后24小時內硬化,幾乎變得很脆,在板柵框等處產生裂痕。

For successful casting operations, once a grid alloy has proven satisfactory, it is important that the specified tolerance be held within the limits . 為使鑄造操作順利進行,一旦證實板柵合金適于鑄造,保持規定的容差在限度范圍內是很重要的。

The center unit carries the grid casting from the mold through the trimming die and finally drops it off the conveyor to a collecting tray . 中間的單元帶著板柵鑄件從模具通過整修模,最后從傳送帶上將它置落到收集架上。

This provides enough of a ribbon of paste so that it will adhere to the belt and pull away from the edges of the grid frames . 這樣能保證有足夠的一條膏帶粘在棉織帶上,同時可除去板柵四框上的余膏。

Adjacent to the table is the third unit which contains a belt conveyor, a grid trimming die and another belt conveyor . 與工作臺相鄰的第三個裝置,包括傳送帶,板柵修邊用模具和第二條傳送帶。

Thus the value of the function at any grid point is the average of its values at the immediately neighboring points . 因此,任一結點上的函數值就等于其直接鄰點上函數值的平均。

The formed active material in the stamped grids becoming loose in the grid openings and the battery failed . 沖孔板柵形成后的活性物質在板柵的孔中變得松散,因而使蓄電池失效。

At any point the convergence is the angle between the meridian as represented on the plane and the n grid line . 一點上的收斂角是子午線在平面上的投影與N坐標線之間的角度。

To justify such shapes, a variety of claims were made, including increased grid structure strength . 為證實這些形狀的合理性,提出了種種論證,其中包括增加板柵的結構強度。

The conductor-length problem was solved by forming the required length of wire into a grid pattern . 電阻絲長度問題,是采取將所需長度的金屬絲做成柵狀結構的辦法解決的。

It is not so easy a matter however to fabricate a grid which will polarize light, but it has been done . 然而要做一個讓光起偏的線柵則不那樣容易,但是究竟還是做出來了。

This operation provides positive opening and closing action thereby reducing “flash“ on the grids . 這種操作起到了良好的開模和閉模作用,因而減少了板柵上的“毛刺”。

This operation provides positive opening and closing action, thereby reducing “flash“ on the grids . 這種操作具有良好的開模和閉模作用,因而減少了板柵上的“毛刺”。